Product Name:KS-407
这是一台二合一真空分离机，即可以分离手机，也可以分离平板。具有宽电压，噪音小，内置真空泵等特点，插上电源就可以使用。
Barcode (EAN)
Product Details
Product Norm
Aftermarket Service
分离手机操作步骤:
1.打开电源开关，温度设置为80度，2-3分钟左右加热台达到80度后。
2.把硅胶垫对好孔放到加热台上，屏幕朝下盖住加热台气孔。
3. 按下S2键，将屏幕吸住后，使用钢丝将液晶和盖板分离，取下液晶屏，分离完成。
分离平板操作步骤:
1.打开电源开关，温度设置为80度，2-3分钟左右加热台达到80度后。
2.把硅胶垫对好孔放到加热台上，屏幕朝下盖住加热台气孔。
3. 按下S1+S2键，将屏幕吸住后，使用钢丝将液晶和盖板分离，取下液晶屏，分离完成。
1.打开电源开关，温度设置为80度，2-3分钟左右加热台达到80度后。
2.把硅胶垫对好孔放到加热台上，屏幕朝下盖住加热台气孔。
3. 按下S2键，将屏幕吸住后，使用钢丝将液晶和盖板分离，取下液晶屏，分离完成。
分离平板操作步骤:
1.打开电源开关，温度设置为80度，2-3分钟左右加热台达到80度后。
2.把硅胶垫对好孔放到加热台上，屏幕朝下盖住加热台气孔。
3. 按下S1+S2键，将屏幕吸住后，使用钢丝将液晶和盖板分离，取下液晶屏，分离完成。
Steps to separate the phone:
1. Turn on the power switch, set the temperature to 80 degrees, and after the heating table reaches 80 degrees in about 2-3 minutes.
2. Place the silicone pad on the heating table with the holes aligned, and cover the heating table air holes with the screen facing down.
3. Press the S2 key, after sucking the screen, use a steel wire to separate the liquid crystal from the cover, remove the liquid crystal screen, and the separation is complete.
Steps to separate the plate:
1. Turn on the power switch, set the temperature to 80 degrees, and after the heating table reaches 80 degrees in about 2-3 minutes.
2. Place the silicone pad on the heating table with the holes aligned, and cover the heating table air holes with the screen facing down.
3. Press the S1+S2 keys, after sucking the screen, separate the liquid crystal and the cover plate with a steel wire, remove the liquid crystal screen, and the separation is completed.
1. Turn on the power switch, set the temperature to 80 degrees, and after the heating table reaches 80 degrees in about 2-3 minutes.
2. Place the silicone pad on the heating table with the holes aligned, and cover the heating table air holes with the screen facing down.
3. Press the S2 key, after sucking the screen, use a steel wire to separate the liquid crystal from the cover, remove the liquid crystal screen, and the separation is complete.
Steps to separate the plate:
1. Turn on the power switch, set the temperature to 80 degrees, and after the heating table reaches 80 degrees in about 2-3 minutes.
2. Place the silicone pad on the heating table with the holes aligned, and cover the heating table air holes with the screen facing down.
3. Press the S1+S2 keys, after sucking the screen, separate the liquid crystal and the cover plate with a steel wire, remove the liquid crystal screen, and the separation is completed.
